preloader

Easier than you imagine

Most of the Far Infrared Heaters by Royal Infrared Heating® can be mounted without help of a professional electrician. Our products are developed and designed primarily for the efficient heating and ease of implementation.

Only four holes are needed to be drilled in a wall to perform an installation. Installation kit comes with each unit. Below you can see the step-by-step Installation Guide.

For a hard-wired installation we recommend to use an assistance of any local electrician. The hardwired installation is easy as to hardwire a TV or any electrical appliance. No extra line needed in most of the cases. Simply hardwire the heater to the closest electrical outlet/box.

Keep in mind that our company does not provide installation, however, our managers can assist you finding an electrician and will also provide you with a helpful installation advice if requested.

Still need assistance with an installation? E-mail us for more details at info@royal-infrared.es.

mounting-installation-far-infrared-mirror-heater-repulsus-royal-infrared-heating-ver1-min

Remove all the protective films

Please make sure to remove all the protective films (both on the front and back)! On the front - blue film and a small sticker at the top right corner. On the back - the blue film.

Wall mounting

This Installation Guide is for Wall Mounting (both vertical and horizontal) as Repulsus model is for wall mounting only! Please do NOT mount this model to a ceiling.

Mounting brackets

There is no need to pre-install any parts. The mounting brackets are attached to the device and allow you easily fit the heater to a wall with a help of only 4 screws.

Heater position recommendation

Our recommendation is to mount the heater in the middle or bottom part of any wall for the best heating efficiency.

In terms of positioning of the heater in the heated room/area, the best is to mount it as close as possible to the area where you or your guests spend most of the time.

Indeed, overtime the infrared waves will reach all surfaces providing an even temperature, but you will still feel more heat close to the heater.

Thus, you may want to mount the heater in the middle of the heated room/area to help spreading the heat as even as possible. 

However, if you have a limited number of wall parts to mount the heater, always feel free to mount the heater to any available  part. It will not simnifically change the efficiency of the IR heating.

Power source

Plug it in

If you want simply plug the heater in a socket, please make sure the socket is located nearby or you use a proper quality socket-extension. By default the electrical cord length is 1.9m. You can cut it and extend if needed.

Or hardwire it

If you want to hard-wire the heater, you can use any closest electrical outlet/box or even any socket or light switcher to get to the electrical line. You can easily cut the electrical cord and extent it as much as needed.

MOUNT THE HEATER

1. Mounting position & minimum distances

Choose the mounting position on any appropriate wall part. Higher you mount the mirror heater Repulsus, more time they will take to heat a room/area.

Please keep the required (indicated on the image) minimum distances.

The IR heater Repulsus is safe to touch, however we always recommend to keep at least 10-30cm from the nearest furniture/curtain or interior object for the safety reasons.

You are responsible for choosing the appropriate installation position.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-1-min

2. Mark the positions

Mark the positions for the four holes onto the drilling template (D) if there are no existing marks. Stick the drilling template on the wall. Find the size of your heater Repulsus:

  • Repulsus 500W - 120 x 60cm - ANHQ (reference points on the drilling template)
  • Repulsus 350W - 100 x 60cm - AEHK (reference points on the drilling template)

Drill the holes with a 8mm rotary bit.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-2-min

3. Insert the screws

Insert the screws into the dowels and fasten the screws. The screws should protrude approximately 0.5 cm from the dowels.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-3-min

4. Hang the heater

Hang the mirror Repulsus (A) on a wall using 4 screws. The brackets are designed for an easy and safe installation process. Make sure you fit both brackets.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-4-min

5. Slide the heater

Slide the mirror Repulsus to make the screws into the correct positions as shown on below image.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-5-min

6. Plug the heater

Plug the mirror Repulsus in to start using it. Please note that the model Repulsus cannot be used with plug-in, nor mains-powered thermostat. Only manual on/off control for both the heating element and LED backlight.

far-infrared-towel-heater-linteum-installation-guide-mount-heater-step-6-min

IR Mirrors Repulsus

The Innovative Far Infrared Heater for an efficient and comfortable indoor heating

sun-180x180-min

GO INFRARED

Feel the Sunshine at home - pleasant and very efficient innovative heating solution

health-180x180-min

STAY HEALTHY

Far Infrared Heating is organic, safe and used a lot in the sports and health facilities

power-180x180-min

SAVE MONEY

Far Infrared Heaters consume less energy and help saving money long-term

controls-180x180-min

BE SMART

Smart WiFi controls with app and voice to control our IR heaters remotely

ROSH3
CE2
GS
EMC
SAA2
fsc
LVD
error: The content is protected.
Shop
0 Compare
0 items Cart
Open WhatsApp
1
💬 Chat in WhatsApp
Still can't make a choice? Chat with us in WhatsApp to schedule a call consultation.